Where to Buy
Please note that product availability may vary by location.
PowerLags®
ExteriorPowerLags®
HEX HEAD HCR® POWERLAGS®
SPAX® Hex Washer Head PowerLags® with HCR® coating are intended for wood to wood connections in exterior structural applications. These fasteners are designed with a hex head conventional driver system along with a built in washer for applications requiring superior pull-down force. Often used in high torque applications.
Available in: 1/2", 1/4", 3/8", and 5/16" diameters
Purchase Options:
Material & Coating
Cold-rolled carbon steel wire heat treated for strength and durability and plated with an HCR® (High Corrosion Resistance) double barrier coating. HCR® is tested and recognized for use in ground contact pressure treated lumber for exterior, freshwater general construction applications. (e.g., AWPA UC1-UC4A, UCFA)
Features
PowerLags® are the ideal replacement for conventional lags!
- No pre-drilling required (1/4" and 5/16")
Note: Lead holes of 11/64" (0.172") diameter is required for 3/8" and 13/64" (0.203") diameter is required for 1/2" PowerLags®
- Heat treated for strength and durability
- IRC / IBC Code Compliant DrJ TER No. 1912-07 Structural Fastener Properties
- Serrated threads require up to 40% less driving torque to increase installation speed while helping prevent cracking in logs
- Built-on washer head designs eliminate the need and extra cost of a separate washer
- Fastener length stamp on the head provides convenient identification without measuring and aids on-site inspections
- Sold in job-friendly package quantities, including bulk pails
SPAX ENGINEERED FASTENERS ARE THE MOST ADVANCED FASTENER PRODUCT ON THE MARKET
Typical Applications
- Deck ledger to band joist attachment
- Exterior treated lumber pergolas and gazebos
- Landscaping timber
- Outdoor furniture
- Exterior fencing
- Decorative applications
Videos
SPAX PowerLags Hex Washer Head HCR Structural Construction Lag Screws
SPAX® PowerLags® Hex Wafer Washer Head structural construction lag screws with High Corrosion Resistance (HCR®) coating.
The Best Structural Screws For Deck Ledger Installation SPAX® POWERLAGS®
SPAX® 5/16” HCR PowerLags require up to 50% fewer fasteners than competing structural screws for deck ledger board installation applications
Downloads
Application Guides
Code Reports
Reference Lateral Shear Values
Product Submittals
Product Brochures
Technical Bulletins
CAD & Dimensional Drawings
Download AllDesign Values & Loads
Southern Pine(SG=.55)
| Diameter | 1/4" | 5/16" | 3/8" | 1/2" |
|---|---|---|---|---|
| Withdrawal W (lbs./inch) | 375 | 415 | 465 | 445 |
| Head Pull-Through WH (lbs.) | 700 | 755 | 985 | 1185 |
Douglas Fir(SG=.50)
| Diameter | 1/4" | 5/16" | 3/8" | 1/2" |
|---|---|---|---|---|
| Withdrawal W (lbs./inch) | 310 | 300 | 300 | 275 |
| Head Pull-Through WH (lbs.) | 640 | 680 | 825 | 970 |
Hem Fir & Spruce-Pine-Fir(SG=.42)
| Diameter | 1/4" | 5/16" | 3/8" | 1/2" |
|---|---|---|---|---|
| Withdrawal W (lbs./inch) | 245 | 250 | 280 | 275 |
| Head Pull-Through WH (lbs.) | 455 | 500 | 575 | 865 |
ALLOWABLE WITHDRAWAL (W) AND HEAD PULL-THROUGH (WH)
- “Withdrawal” and “Head Pull-Through” design values shall be adjusted by all applicable adjustment factors per NDS Table 11.3.1.
- “Withdrawal” design values are to be multiplied by the length of the thread penetration into the side grain of the main member. Length includes tip.
- “Withdrawal” design values are from the main member, and “Head Pull-Through” design values are based on a minimum of 1-1/2" side member thickness.
- Tabulated “Withdrawal” and “Head Pull-Through” design values are for the wood species with the listed assigned specific gravities. Where the wood species assigned specific gravity is not listed, use the next lower assigned specific gravity values.
Learn More About SPAX® Powerlags®
Featured Applications
VIEW ALLExterior